- Model NO.: WH166
- Emitting Color: Changeable
- Application: Diving
- Voltage: 90V-260V
- Model Item: Wh166 LED Underwater Light
- Modes: High>Medium> Low>Red> off
- Color Temperature: 5000k (White Light);
- Light Head: with Mounting Connector Default One Light Read, Ca
- Surface Treatment: Premium Type III Hard-Anodizing.
- Trademark: ARCHON
- Origin: Shenzhen of China
- IP Rating: IP68
- With Light Source: With Light Source
- Lamp Body Material: Aluminum
- Certification: CE, RoHS
- Bulb: White CREE Xm-L2 U2 LED *12 (Max 6500 Lumens);
- Runtime: High (3.0h); Medium (4.0h); Low (10.0h); Red (10.0
- Reflector: No Hotspot Design, No Reflector;
- Angle of Light Beam: 120 Degree
- Battery: Rechargeable Li-ion Battery Pack (26650 Battery *
- Specification: CE, RoHS
- HS Code: 85131010
2. Bulb: White CREE XM-L2 U2 LED *12 (max 6500 Lumens);
Red CREE XP-E N3*4 (wavelength 620nm, max 400 Lumens)
3. Modes: High>Medium> Low>Red> off
4. Runtime: : High (3.0h); Medium (4.0h); Low (10.0h); Red (10.0h)
5. Color temperature: 5000K (white light);
6. Reflector: No hotspot design, no reflector;
7. Lens: 5mm Polycarbonate Board;
8. Light head: With mounting connector default one light read, can use
Two light heads also. (optional)
9. Body material: Durable aircraft-grade aluminum.
10. Angle of light beam: 120° ;
11. Surface treatment: Premium Type III hard-anodizing.
12. Color: Black
13. Battery: Rechargeable Li-ion battery pack (26650 battery *8)
14. Battery Indicator: 100%-50%: Green; 50%-30%: Yellow; 30%-10%:
Red; Below 10%: Red Flashing; Below 5%: Switch off;
15. Can be charged directly on the light, with battery over-discharging
Protection
16. Fully charging time: 8-10h;
17. With gas release valve
18. Operation voltage: 12V to 18V;
19. Waterproof: 100 meters underwater
20. Dimensions: 244.5mm (canister length)* 78.2mm (dia. Of canister) *
56.5mm (dia. Of light head);
21. Weight: 2230 grams (with battery pack)
22. Underwater Weight: 1100 grams (with battery pack)
23. Impact resistance: 1.5M.
BATTERY CHARGING
1. Plug the charger in the wall power socket, the indicator light is green
In the free-load status.
2. Open the top cover of the canister plug the plug of the charger in the
Ports on the canister. (the positive and negative polar doesn't matter,
Both ways work. )
3. The indicator light on the charger is red if the battery is not fully
Charged; It will turn green after fully charged.
4. Take out the charger, put the cover on the canister and use the light.
ON/OFF
Push the switch to turn it ON.
MODES CHANGING
Successive push the switch ON-OFF within two seconds to cycle through High, Low, strobe, OFF.
SCUBA DIVING APPLICATION
Check closely for cuts, scratches, or an otherwise damaged O-ring or mating lens surface as this can cause the light to flood under pressure. Remove any salt deposits, sand, dirt, or other foreign matter from the O-ring sealing surfaces.
KEEP THE THREADS, O-RING GROOVE LUBRICATED WITH SILICONE GREASE.
CAUTION
Please put the switch on the canister to the position of "OFF" during transportation to prevent it from misoperation.
If the switch gets stuck, please put some washing-up liquid in the slot of the switch and push the switch back and forward several times till it move smoothly again, then clean the light in the fresh water.
Please charge the light every time after using. If it isn't used for a long time, please charge the light once every 3 months to prepare for next time using.
Automotive Connectors,Automotive Connector,Cable Wire Connectors,Cable Wire Connector
YUEQING WEIMAI ELECTRONICS CO.,LTD , https://www.weimaiconn.com